聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

超声波辅助微波消解预处理测量污泥金属元素

以实验室污泥和污水厂污泥为研究对象,建立了超声波辅助微波消解预处理测量污泥金属元素的方法与程序。首先通过超声波分散污泥絮体,然后对污泥进行加热预处理和微波消除,最后采用火焰原子吸收法测量污泥中的金属元素。结果表明,150 W超声波作用于25 mL污泥3 min为超声波分散污泥的较优条件,能保证后续操作过程取样均匀。微波消解前适宜的加热预处理条件为90℃,20 min。实验室污泥微波消解的较优酸体系为2 mL双氧水＋4 mL反王水（或4 mL王水）;污水厂污泥微波消解的较优酸体系为1 mL氢氟酸＋2 mL双氧水＋4 mL王水,同时,第3阶段消解条件为压强2.0 MPa下消解20 min。超声波辅助微波消解预处理具有用酸量少、简易快捷、准确度和精密度高等优点,测量K,Ca,Mg,Fe的相对标准偏差≤2.75%,加标回收率为97.5%～102%。     

Optimization of resistance spot brazing process parameters in AHSS and AISI 304 stainless steel joint using filler metal

The aim of this research study was to determine optimal resistance spot brazing parameters for joining between AHSS and AISI 304 stainless steel by using filler metal. The key parameters investigated in this study consist of the brazing current, electrode pressure and brazing time. The Taguchi method was applied to the design of experiments. Signal-to-Noise ratio was introduced in the study to identify optimal levels from the process where input parameters yield increased shear strength. Brazing was thus implemented with 5,000A brazing current, 0.70 MPa electrode pressure, and 1.50s brazing time. The maximum shear strength obtained was 54.31 N·mm⁻² in accordance with input parameter settings. In addition, Cu-rich phase and Ag_0.4Fe_0.6 intermetallic phases were found at the interface zone.     

Effect of fusion welding processes on tensile properties of armor grade,high thickness,non-heat treatable aluminium alloy joints

AA5059 is one of the high strength armor grade aluminium alloy that finds its applications in the military vehicles due to the higher resistance against the armor piercing (AP) threats. This study aimed at finding the best suitable process among the fusion welding processes such as gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) by evaluating the tensile properties of AA5059 aluminium alloy joints. The fracture path was identified by mapping the low hardness distribution profile (LHDP) across the weld cross section under tensile loading. Optical and scanning electron microscopies were used to characterize the microstructural features of the welded joints at various zones. It is evident from the results that GTAW joints showed superior tensile properties compared to GMAW joints and this is primarily owing to the presence of finer grains in the weld metal zone (WMZ) and narrow heat-affected zone (HAZ). The lower heat input associated with the GTAW process effectively reduced the size of the WMZ and HAZ compared to GMAW process. Lower heat input of GTAW process results in faster cooling rate which hinders the grain growth and reduces the evaporation of magnesium in weld metal compared to GMAW joints. The fracture surface of GTAW joint consists of more dimples than GMAW joints which is an indication that the GTAW joint possess improved ductility than GMAW joint.     

焊接切割与火灾

焊割火灾事故呈上升趋势。文章分析了焊割火灾爆炸危险性,并提出了预防措施。     

功能化离子液体的合成表征及其作为润滑剂的性质

通过两步法合成了含酯基官能团的咪唑类离子液体1-乙酸乙酯基-3-甲基咪唑四氟硼酸盐，用核磁共振、红外光谱、元素分析对其进行了结构表征，证明了该合成方法的可靠性；对功能化离子液体的基本物化性质、熔点、热稳定性及其作为润滑剂的粘温性、蒸发损失、金属腐蚀性等进行了全面研究，并选择了含有相同烷基的1-丁基-3-甲基咪唑四氟硼酸盐传统离子液体进行对比，发现官能团的引入，使传统烷基咪唑类离子液体展现出不同的特性，同时发现两种离子液体均对金属表面有较强的腐蚀作用，为进一步开展功能化离子液体的摩擦学研究打下了基础。     

适用于金属物体识别的L形无芯RFID标签设计

设计了一种L形无芯射频识别标签,该标签包含6个不同尺寸的L形散射单元,利用其交叉极化方向上的反向散射场进行识别。标签基于频域特征进行编码,每个标签可携带6 bit信息。使用CST仿真软件对所设计L形无芯RFID标签进行仿真,分析了L形散射单元的尺寸变化时对标签谐振特性的影响。此外,还仿真了标签的接地板尺寸增加后的情况,证明该标签可适用于金属物体的识别或金属背景下的物体识别。     

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

Effect of welding processes and consumables on fatigue crack growth behaviour of armour grade quenched and tempered steel joints

Quenched and Tempered (Q&T) steels are widely used in the construction of military vehicles due to its high strength to weight ratio and high hardness. These steels are prone to hydrogen induced cracking (HIC) in the heat affected zone (HAZ) after welding. The use of austenitic stainless steel (ASS) consumables to weld the above steel was the only available remedy because of higher solubility for hydrogen in austenitic phase. The use of stainless steel consumables for a non-stainless steel base metal is not economical. Hence, alternate consumables for welding Q&T steels and their vulnerability to HIC need to be explored. Recent studies proved that low hydrogen ferritic steel (LHF) consumables can be used to weld Q&T steels, which can give very low hydrogen levels in the weld deposits. The use of ASS and LHF consumables will lead to distinct microstructures in their respective welds. This microstructural heterogeneity will have a drastic influence in the fatigue crack growth resistance of armour grade Q&T steel welds. Hence, in this investigation an attempt has been made to study the influence of welding consumables and welding processes on fatigue crack growth behaviour of armour grade Q&T Steel joints. Shielded metal arc welding (SMAW) and Flux cored arc welding (FCAW) were used for fabrication of joints using ASS and LHF consumables. The joints fabricated by SMAW process using LHF consumable exhibited superior fatigue crack growth resistance than all other joints.     

NICALON SiC/Al 预制丝热膨胀特性研究

本文研究了NICALON SiC束丝纤维增强铝预制丝在15～400℃温度区间内的热膨胀特性。研究表明预制丝两次热循环后得到的膨胀曲线不一致,该曲线在15～400℃范围的平均热膨胀系数分别为3.2×10~(-6)℃~(-1)、4.1×10~(-6)℃~(-1)。本文对预制丝的热膨胀行为进行了理论分析和探讨,计算值和实验值较为符合。